Vertical cutting dryer is one kind equipment of waste management in oil gas industry. It main used on the drill cutting treatment especially the oil base drill cutting. Last week we delivered one vertical cutting dryer and one Decanter centrifuge to mud company. According to client requirement, all equipment was installed in container for insulation and easily transport in different job site.

As we all know, drill cutting is high pollution since include lots chemical, meanwhile the contented liquid is expensive. Separate the liquid out and recycle it, and dryer the solids. These measure are very important to protect environment and reduce the cost of drilling mud.

In this system there are vertical cutting dryer and Decanter centrifuge. Both devices are utilize same principle. When the machine are in high rotational motion, the inside material will bear separation force. Along with the speed faster, separation G force will be higher. Due to the solids and liquid are different density. They will bear vary separation force. High density bear bigger force, and it will settle down onto the bottom of centrifuge bowl, and liquid will be on higher layer. This program will achieve the solids and liquid separation. After that, the solids and liquid will be discharge from different outlet port.

Decanter centrifuge was designed with higher separation G force, normal can over 3000G. Vertical cutting dryer only about 900 RPG . This different designing lead to the cutting dryer can process the material with high solids content such as drill cutting, but the discharge liquid is not clear . On the contrary, material for Decanter centrifuge normally less than 10% for solids content. But the discharged liquid is much clear. This is why we use Decanter centrifuge for further treating to the liquid discharged from vertical cutting dryer.

Sometimes we use high G shaker to treat water base drill cutting and then use Decanter centrifuge. If you have these kind requirement ,welcome to contact us.

Solids vacuum pump is one of the most featured equipment of GN solids control. It was developed and started to sell in 2017. A brand new equipment for high solids content material transfer. As we all know GN is focused on solids control equipment to serve oil gas industry for petroleum drilling project. His equipment main used to treat the drilling mud ,to recycle it and clean it for reuse. And help customer to reduce the using of drilling mud, and save more.

Actually GN solids control has the centrifuge pump, submersible pump for drilling slurry transfer. But in some other project, client need to transfer the high solids content such as drill cutting that is very viscosity, and sometime with big size particle. The normal pump is no way to this kind material. So we built this solids vacuum pump. Which is driven by high speed pressure air, need air compressor to provide air source to run it. This pump is simple structure with high work performance. Last week we delivered one unit GNSP-40B pump to China customer for the tunnel boring slurry transfer. This project is located in downtown of city. So user need the pump be quiet, we design special device to reduce noise.

This 40B pump can transfer 40 cube meter clean water per hour. The capacity will reduce along with the solids content be higher and higher. This pump has long distance transfer ability, which can reach 1000 meters when transfer clean water, and the most suck distance is about 500 meters. It can be used in most project. However, this pump is poor to suck material for low place. It utilize vertue to generate vacuum to suck the material. So it is poor to suck material from low place. Sometimes ,it also be affected by the location altitude. Please double check with GN before using this pump for your project.

This week we completed 2 sets solids control equipment ,and ready to delivery to Bolivia customer. Last year, we already shipped 2 units Decanter centrifuge to same customer. We are so glad that client give good feedback to our equipment, and also honored that cooperate with this so kind customer who is so professional in solids control area and understand well to GN equipment.

These solids control equipment running well under the operation of our client , and bring profit to them. In this order, there are total 4 units decanter centrifuge, and 8 units centrifuge and 2 units screw pump. Each screw pump is used to feeding slurry to Decanter centrifuge. all equipment were 100% designed and manufactured by GN. The core equipment of this solids control equipment is Decanter centrifuge. GNLW363-VFD is the most featured products for solids control using in oil gas industry. Whatever the water base drilling mud or oil base mud, GNLW363-VFD can treat them with good effect. This is profit from our team keep upgrading the design and strictly quality control during manufacturing. GN has strict and high requirement to supplier, we care money, but more concern quality. Almost all the supplier is from the famous brand of global or China. Such as the bearing, paint, electrical component etc. The centrifuge was design according to the most harsh situation. We are always happy and open to hear advice from customer, actually we keep collecting the quality feedback from customer, and adjust design to make it more popular by customer. Decanter centrifuge is just one of products. We can provide the whole series solids control system, built customized mud system specially for client project. The good quality and quick service helped us to get lots long term partner in the global. If your project have demanded on these equipment, welcome to contact us.

In pump market ,there seems no one kind pump can transfer high solids content material. In lots project ,people only can transfer them by manual. That is a low efficiency way and the expensive labor will reduce profit. GN Solids control main built solids control for drilling mud treatment in oil gas industry. The drilling mud will be separated out solids with our solids control equipment such as shale shaker ,Decanter centrifuge .In some drilling project, client will use oil base mud, the liquid is crude oil or diesel. The contented solids is highttps://gnsolidscontrol.com/h viscosity. The traditional pump is useless. GN designed this solids vacuum pump for this application of high solids content material transfer.

Last week we delivered 2 pumps to Africa, they will be used in petroleum well drilling project. Transfer the drill cutting. Different with traditional pump, vacuum pump was driven by high pressure air. There is no electrical component on this equipment , even the control component also use air. This no electric design make this pump can be used in some place that high requirement to the explosion proof. This pump utilize Venturi to generate vacuum space inside of pump tank , and then suck the material into tank. After the tank be full with material, pump will switch to discharge model. High pressure air will push material out pump tank and discharge. This simple design make the pump stable and high efficiency. Our biggest model GNSP-40B, which can transfer 40 cube meter water per hour , and discharge distance can reach 1000 meters. This pump is not good at suck material from low place. However, the actual pump capacity is related with the density of material , the viscosity, and also the particle size.

Currently ,we have 40B, 20B,10B,5B these 4 models. The other new model will be designed in future. If your project have demand on this kind pump, welcome to contact us to get more information.