Last week GN Delivered 5 vertical cutting dryer and 10 units Decanter centrifuge to Nigeria. All these equipment were used for oil base mud treatment, the vertical cutting dryer are install after shale shaker of solids control system, which is used to dryer the drill cutting and recycle the involved mud inside of solids. Nigeria is one of our biggest market, and we had cooperate with this customer for more than 10 years. The client purchase from GN almost every year.

In this order, client required discharged from all machine without dropping on ground. Directly transfer the discharged machine into next machine without stop and non pollution to environment. In the case, we add lots screw conveyors to catch the solids and transfer them to next machine. For example, the screw conveyor will directly receive the solids from shale shaker and feed them into vertical cutting dryer. Below the vertical cutting dryer, there are also equipped screw conveyor，when the solids discharged from vertical cutting dryer, the conveyor will transfer them to truck and transport them to other site for further treatment. Same with shale shaker and vertical cutting dryer, below the Decanter centrifuge ,there are also installed screw conveyor. Between the vertical cutting dryer and Decanter centrifuge , there are screw pump to pump the discharged liquid to centrifuge. These liquid after treatment by centrifuge ,it will clean enough to back to mud system for reuse.

Oil base mud is very expensive material for the well drilling, and it is also important to improve the drilling efficiency and cooling the rig and protect the rig ,and also balance the pressure between inside and outside or machine. Our solids control equipment is aim to keep the good property of drilling mud. And recycle as much as possible from drill cutting, that is helpful to reduce the cost of drilling and improve efficiency. If you have demanded on these equipment, welcome to contact us.

With more than 15 years development, GN solids control accumulate large experience about the separation equipment design and manufacture, especially on the oil gas industry for drilling mud treatment. We are very good at manufacture the customized solids control system and also provide the special technical support. Last week we delivered sever sets mud cleaner for offshore drilling.

The mud cleaner is combination of shale shaker ,desander, and desilter. On the offshore. One machine can treat the sludge for 3 times to remove out different size particle, And the machine only need small area for layout. Compare with onshore drilling ,the offshore or drilling fleet both have more strictly requirement to equipment on explore proof standard, the lifting standard. Most time offshore will need DNV certificate to guarantee the lifting eyes are strong enough. For some electrical motor ,offshore always require some special certificate. GN provide many equipment to offshore drilling project, and we are totally can satisfied with client demand. Mud cleaner is one of the most important equipment after shale shaker in solids control system. It include 2 units 10 inch hydrocyclone and 12 units 4 inch hydrocyclone and also the bottome shaker. Centrifuge pump will feed slurry to 10 inch hydrocyclone first and remove out the particle bigger than 60um. The discharged solids will drop on the bottom shaker to dryer the solids.  Then one more centrifuge pump will feed slurry from bottom tank to 4 inch centrifuge, 4 inch centrfiuge can remove out particle bigger than 20um. For most project, the slurry after treatment by mud cleaner, it would be enough to recycling. However, if the jobsite require more clean slurry, we can add one extra Decanter centrifuge to remove out the tiny solids smaller then 20um.

The stable solids control equipment can help client to recycle more drilling mud and save the money for customer. GN are very professional on this field, if you have demanded on these equipment, welcome to contact us.

GN Solids Control was fund in 2005, as begin we main main manufacture solids control equipment for oil gas industry such as shale shake, mud cleaner, Decanter centrifuge. These equipment are used for drilling mud treatment. With the development and also the accumulation of technology, till now GN not only serve oil gas industry but also also separation application such as mining industry, waste water treatment. However, oil gas industry is still main industry for us to serve.

Last week we delivered one set solids control equipment to Africa customer, which include two units shale shaker, one unit mud cleaner and also one unit decanter centrifuge. Actually client also need some mud tank for this system ,but we suggest client to made tank in their local, GN will provide all design drawing of tank, that will help client to save money. Because the tank shipping cost will be very expensive. GN equipment was very popular in Africa market, compare with other solids control supplier. GN solid control manufacture according API standard, and every year API institute will inspect our company to make sure everything of GN will comply with API standard. except the stable quality, GN also have very competitive price compare with other supplier. Till now we have exported to more than 76 countries.

In this order, these equipment are used for one 1500HP rig system, 1500 rig system usually can drilling 1500~2000 meters well, the treating capacity is not very big. So client only buy one unit GN 14 inch Decanter centrifuge. It will be used to remove the tiny particle when the drill mud was recycled many times and accumulated much tiny particle that the shale shaker and mud cleaner can not remove them out , this time we need to start Decanter centrifuge to separate out these tiny particle through the high separation G force.

Tech support is the always provided quickly, if you have demand on solids control equipment, welcome to contact us any time.

last week GN delivered one mini shale shaker and one mini vacuum pump to south America customer. These equipment are used for oil gas industry. The customer who purchased this 2 units equipment is a very famous tank manufacture in the global. We do respect their quality and their quality management. They always provide excellent product to customer ,so they have have very strictly requirement to their supplier. We are honored that client have lots trust to us, and give us lots order.

Client purchase these two units equipment are used for cleaning huge tank. Client built tank with 35-50 feet depth, they need spend lots cost to clean the tank. For this depth , it is also very hard to get out the dirty water after clean tank. And the water consumption is also big issue and spend lots money to treat these waste water. GN mini shale shaker are spending designed to cleaning the tank bottom , which can instead people to suck the dirty solids and sludge. and directly transfer these sludge with more than 500 meters. It just like a big vac cleaner ,but GN vacuum pump can do more ,can suck than bigger dryer solids and viscosity sludge. This pump are driven by high pressure air, no spark ,and it can be used in the most danger area.

cooperate with vacuum pump, client also purchase one mini shale shaker, which be used to separate the sludge from vacuum pump. Mini shale shaker utilize the vibration force to separate the solids and liquid away. It can remove out particle that size bigger than 40 micron if we choose higher mesh shaker screen. After the sample treatment by shale shaker, the water can be used again in some project than have low requirement to water quality. Most important is this shaker have very low power consumption.

GN is very professional on the solids control equipment, and waste management, if your project have demand on solids-liquid separation ,we can provide the customs proposal for your project.